Home (Tongue-and-groove)


Home » Home » Tongue-and-groove



Home  Toilet cleaner  Toothbrush

Tongue-and-groove siding is installed to cover two short new wall sections.
Related Articles:
Index of Siding and Trim Articles
Installing Fiber Cement Siding
Repairing Shallow Rot Damage In Wood Siding.

lumber (bois embouveté, m.) Any lumber, such as boards or planks, machined in such a manner that there is a groove on one edge and a corresponding tongue on the other.
tooled joint See joints.

Tongue-and-groove systems
Tighter spacing and tongue-and-groove systems create a slightly different deck appearance and partially shed water.

" A joint made by a tongue (a rib on one edge of a board) that fits into a corresponding groove in the edge of another board to make a tight flush joint. Typically, the subfloor plywood is .

Tongue-and-Groove Pliers: Commonly called by the brand name Channellocks, these pliers are the first tool plumbers reach for when they need to grab, pull, twist, hold, tighten or loosen something. Be sure to get two sizes: 10-in.

Joint where the projection or "tongue" of one member engages the mating groove of the adjacent member to minimize relative deflection and air infiltration; widely used in sheathing, flooring and paneling.

Tongue-and-groove ceilings are composed of interlocking lips intended to hide nails from sight. When it comes to finishing a tongue-and-groove ceiling, success has more to do with procedure than style.

Carpentry joint in which the jutting edge of one board fits into the grooved end of a similar board.
Trap ...

Tongue-and-Groove Joint
A joint formed by the insertion of the “tongue' of one wood member into the “groove' of the other; modifications include tongue and groove rabbet joint, dado tongue and rabbet, tongued shoulder joint, ...

The planks replaced outdated acoustic ceiling tile giving added architectural interest. Hefty crown molding adds to the traditional feel of the space. The granite countertops add a sense of weight and color.

8. The tongue-and-groove chipboard floorboards are held in place with screws. A water-resistant grade is a good choice, and essential in the bath or shower room.

A lower ceiling demarcates the scullery area from the rest of the kitchen.

Used for food prep and washing up, this scullery has an expansive, rustic butcher block counter, two dishwashers and lots of storage space.

Once the tongue-and-groove boards were in place, we needed to cover them as soon as possible with a layer of 15-pound roofing felt. This protects the boards from any rain or moisture you might get during the rest of the roof construction.

Warning: flooring can't be sanded and refinished as many times as planks can. Also, the planks should be at least 3/4 to 7/8 thick.

Blind nailing tongue-and-groove boards hides the fasteners. Each fastener is driven through one board's tongue, and covered by the next adjacent board.

strip, narrow boards, which are cut in random lengths planks, tongue and groove boards, ...

In other cases, tongue-and-groove boards join
together to provide a decorative panel. In yet other
cases, a relatively thick, carved panel is used.
Wainscoting is an affordable way to enrich your room
and add value to your home.

In cases where the gap or coverage is not adjustable, as in flooring, you have to make up part of the discrepancy at the start and the rest at the end. Say you're installing flooring between two walls that are 1 in.

Most ceiling tiles have tongue-and-groove edges for easier installation. You can choose from plain, embossed and patterned finishes.

The well should be cased with a watertight material (for example, precast concrete) and a cement grout or bentoniteclay sealant poured along the outside of the casing to the top of the well.

She wanted the rough-sawn tongue-and-groove interior walls she�d seen at Kauri Cliffs resort in the Bay of Islands; antler chandeliers like those seen in a Sydney clothing shop. But �everything in the house had to be new and perfect for it�.

sanded over the lifetime of the floor, above the portion, is approximately
7/32" approaching 1/4". This type of hardwood flooring can be installed with a nail-down
installation method over wood subfloors.

When removing and reusing tongue-and-groove paneling, drive nails through the tongues with hammer and nailset, then lift the wood away. Drive protruding nails into the wall framing.

Hardwoods such as oak, maple and ash are harvested, sawn and fashioned into boards of various lengths and widths, ranging from 12 to 84 inches in length, 2 ½ to 5 inches wide and ¾ inch thick.

Integrally colored plaster walls and a distressed finish on the tongue-and-groove cabinetry add patina to this new kitchen. Beauharnais limestone was used for the countertop, backsplash, and floor.

Now this is called paneling. Why, because each piece has a tongue and a groove. A tongue on one side, a groove on the other side.

WOODHAVEN CEILING PLANKS Made from medium-density fiberboard, the tongue-and-groove boards won't warp and they clean up with the wipe of a sponge. Available in natural, shown, and white-painted finishes. $3 to $3.25 a square foot.

Build the main door out of 2x6 using clamps to squeeze the four boards tightly together until you get the paired-up battens bolted through on both sides of the door.

Locking Installation System Method of installing laminate flooring with a unique tongue-and-groove profile that allows for easy installation of boards by just locking edges into place and requiring no glue.

- A custom wall unit with panelling defines the storage space and provides a place to keep clothing that's only used occasionally.

The sheathing material may be square-edge, shiplap, tongue-and-groove boards, or plywood or oriented strand board (OSB). Sheathing, in addition to serving as a base for the finished siding material, stiffens the frame to resist sway caused by wind.

Today's log home kits are made of milled solid timbers that use a variety of interlocking methods to eliminate air and water infiltration. In addition the joints are usually sealed with plastic caulking and gaskets.

Matchboarding: Form of cladding where long wooden boards are held together with tongue-and-groove joints.
Matelassé: A double-woven fabric with puckered surface effects.
Matte Finish: A finish that's more flat than shiny.

Siding Material Calculator
Siding Terminology
Siding Vertical Installation
Siding - Vinyl Installation
Soffit & Fascia Installation
Stucco Repair ...

Pine paneling comes in a variety of styles. A style common in mid-20th century homes is tongue-and-groove knotty pine. Newer pine paneling styles have a flat surface or a pronounced V-groove. The ...
How to Plant Leonotis Nepetifolia ...

* the toilet and sink plumbing can be hidden by white-painted, boards
* mahogany-throne commode, complete with arms and a rattan lid
* claw-foot tub ...

All of their teak is FSC certified, and the solid tongue-and-groove boards should last a long time in your home.
Rate: ...

Beadboard: A form of paneling, traditionally made of wood, with boards running the height of the panels. Also called wainscoting.

You can easily create the effect of wood and give your ceiling texture and depth by using plywood panels, tongue-and-groove board paneling (also called beadboard) and mineral fiber planks that imitate wood.

Strip Flooring. The most popular wood flooring, strip flooring is made of narrow (approx. 3-inches wide) boards that are end-matched. Strip flooring wider than 3 inches is called plank flooring.

See also: See also: Home, Floor, House, Design, Wood

Home  Toilet cleaner  Toothbrush

RSS Mobile